Anyone here tried the Xeon E5-2651 V2?

Iaroslav · Nov 15, 2017

its said:
About 840 h/s. Get the e5 2660 v2. It hits 980 h/s and it is $10 cheaper on ebay.

SR1AB INTEL XEON E5-2660V2 10 CORE 2.20GHz 95W PROCESSOR FOR DELL T5600 C8220 | eBay

Ah, I've already ordered pair of these 2651. Thank you for for the information.
BTW, mine E5-2660v2 hit 1034 H/s on xmr-stak

kfriis · Nov 27, 2017

I am seeing about 1060 H/s on dual 2660V2 using old xmr-stak on bare metal.

Sent from my ONEPLUS A5000 using Tapatalk

Joel · Nov 29, 2017

kfriis said:
I am seeing about 1060 H/s on dual 2660V2 using old xmr-stak on bare metal.

Sent from my ONEPLUS A5000 using Tapatalk

Dang, that's more than my 2x2667v2 board was getting, but I was just running XMRIG with zero config. I suspect I should get ~1200 if I actually set up NUMA affinity. It's offline for the time being though, moving house...

kfriis · Nov 30, 2017

@Joel

Yeah - you should for sure get higher hashes than me. Feel free to ask me if you have any questions and I will be happy to help.

Note that I am running xmr-stak though. I did not find xmrig to be that good despite quite a bit of testing.

Joel · Nov 30, 2017

Ah that's good to know. I'll have some time to play with it on Saturday, after installing my two Vega 64s.

Bradford · Jan 19, 2018

Iaroslav said:
Ah, I've already ordered pair of these 2651. Thank you for for the information.
BTW, mine E5-2660v2 hit 1034 H/s on xmr-stak

Have you had a chance to test them? If so, how did they perform on Monero, and what was their power draw? Thanks

azev · Jan 19, 2018

Bradford said:
Have you had a chance to test them? If so, how did they perform on Monero, and what was their power draw? Thanks

I am interested in this too, have 2 more nodes with v1 that can use an upgrade.

Iaroslav · Jan 20, 2018

Bradford said:
Have you had a chance to test them? If so, how did they perform on Monero, and what was their power draw? Thanks

I tried few configs, but no luck:
Totals: 888.1 888.8 888.6 H/s
Highest: 891.4 H/s
Power draw is similar to 2660v2 I think, maybe later I'll measure it on my quanta setup.

marcoi · Jan 20, 2018

Code:

Architecture:        x86_64
CPU op-mode(s):      32-bit, 64-bit
Byte Order:          Little Endian
CPU(s):              24
On-line CPU(s) list: 0-23
Thread(s) per core:  1
Core(s) per socket:  12
Socket(s):           2
NUMA node(s):        2
Vendor ID:           GenuineIntel
CPU family:          6
Model:               62
Model name:          Intel(R) Xeon(R) CPU E5-2651 v2 @ 1.80GHz
Stepping:            4
CPU MHz:             1795.665
CPU max MHz:         2200.0000
CPU min MHz:         1200.0000
BogoMIPS:            3591.33
Virtualization:      VT-x
L1d cache:           32K
L1i cache:           32K
L2 cache:            256K
L3 cache:            30720K
NUMA node0 CPU(s):   0-11
NUMA node1 CPU(s):   12-23
Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid dca sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm cpuid_fault epb pti tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms xsaveopt dtherm ida arat pln pts

Code:

[100%] Built target xmrig
 * VERSIONS:     XMRig/2.3.1 libuv/1.9.1 gcc/6.3.0
 * HUGE PAGES:   available, enabled
 * CPU:          Intel(R) Xeon(R) CPU E5-2651 v2 @ 1.80GHz (1) x64 AES-NI
 * CPU L2/L3:    3.0 MB/30.0 MB
 * THREADS:      12, cryptonight-lite, av=2, donate=0%
 * COMMANDS:     hashrate, pause, resume
[2018-01-20 05:28:59] speed 2.5s/60s/15m 1428.0 1427.8 n/a H/s max: 1428.0 H/s

I have two threads, each doing 1430 H/s. Whole server, Intel is doing Average of 375W which includes two 1050 ti 4GB cards mining.
Server idles at 173W
with miner1 running up to 220w
with miner2 running up to 270w
With nvidia running up to 397W

I have HT disabled in bios and am running dockers images.

Joel · Jan 20, 2018

marcoi said:

Code:

Architecture:        x86_64
CPU op-mode(s):      32-bit, 64-bit
Byte Order:          Little Endian
CPU(s):              24
On-line CPU(s) list: 0-23
Thread(s) per core:  1
Core(s) per socket:  12
Socket(s):           2
NUMA node(s):        2
Vendor ID:           GenuineIntel
CPU family:          6
Model:               62
Model name:          Intel(R) Xeon(R) CPU E5-2651 v2 @ 1.80GHz
Stepping:            4
CPU MHz:             1795.665
CPU max MHz:         2200.0000
CPU min MHz:         1200.0000
BogoMIPS:            3591.33
Virtualization:      VT-x
L1d cache:           32K
L1i cache:           32K
L2 cache:            256K
L3 cache:            30720K
NUMA node0 CPU(s):   0-11
NUMA node1 CPU(s):   12-23
Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid dca sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm cpuid_fault epb pti tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms xsaveopt dtherm ida arat pln pts

Code:

[100%] Built target xmrig
 * VERSIONS:     XMRig/2.3.1 libuv/1.9.1 gcc/6.3.0
 * HUGE PAGES:   available, enabled
 * CPU:          Intel(R) Xeon(R) CPU E5-2651 v2 @ 1.80GHz (1) x64 AES-NI
 * CPU L2/L3:    3.0 MB/30.0 MB
 * THREADS:      12, cryptonight-lite, av=2, donate=0%
 * COMMANDS:     hashrate, pause, resume
[2018-01-20 05:28:59] speed 2.5s/60s/15m 1428.0 1427.8 n/a H/s max: 1428.0 H/s

I have two threads, each doing 1430 H/s. Whole server, Intel is doing Average of 375W which includes two 1050 ti 4GB cards mining.
Server idles at 173W
with miner1 running up to 220w
with miner2 running up to 270w
With nvidia running up to 397W

I have HT disabled in bios and am running dockers images.

I note that's for Aeon, I think folks were asking about XMR hash. Could you be so kind as to get a quick read on XMR?

I think 10 threads on the physical cores, plus 4 threads on HT cores would be a good place to start.

Bradford · Jan 20, 2018

Iaroslav said:
I tried few configs, but no luck:
Totals: 888.1 888.8 888.6 H/s
Highest: 891.4 H/s
Power draw is similar to 2660v2 I think, maybe later I'll measure it on my quanta setup.

That was with 2 CPUs?

marcoi · Jan 20, 2018

Code:

[2018-01-20 13:57:10] Using JSON-RPC 2.0
[2018-01-20 13:57:10] Starting Stratum on stratum+tcp://xmr.pool.minergate.com:45560
[2018-01-20 13:57:10] 30 miner threads started, using 'cryptonight' algorithm.
[2018-01-20 13:57:10] Pool set diff to 1063
[2018-01-20 13:57:10] Stratum detected new block
[2018-01-20 13:57:11] accepted: 1/1 (100.00%), 719.90 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:12] accepted: 2/2 (100.00%), 716.61 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:19] accepted: 3/3 (100.00%), 710.53 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:24] accepted: 4/4 (100.00%), 712.24 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:24] accepted: 5/5 (100.00%), 707.54 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:27] accepted: 6/6 (100.00%), 725.14 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:27] accepted: 7/7 (100.00%), 732.42 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:28] Pool set diff to 4148
[2018-01-20 13:57:28] Stratum detected new block
[2018-01-20 13:57:33] accepted: 8/8 (100.00%), 717.00 H/s at diff 4148 (yay!!!)
[2018-01-20 13:57:40] accepted: 9/9 (100.00%), 709.72 H/s at diff 4148 (yay!!!)
[2018-01-20 13:57:41] Pool set diff to 5310
[2018-01-20 13:57:41] Stratum detected new block
[2018-01-20 13:57:41] accepted: 10/10 (100.00%), 715.22 H/s at diff 5310 (yay!!!)
[2018-01-20 13:57:57] accepted: 11/11 (100.00%), 747.94 H/s at diff 5310 (yay!!!)
[2018-01-20 13:58:45] accepted: 12/12 (100.00%), 750.64 H/s at diff 5310 (yay!!!)
[2018-01-20 13:58:53] accepted: 13/13 (100.00%), 721.28 H/s at diff 5310 (yay!!!)
[2018-01-20 13:59:02] accepted: 14/14 (100.00%), 716.12 H/s at diff 5310 (yay!!!)
[2018-01-20 13:59:19] Pool set diff to 3206
[2018-01-20 13:59:19] Stratum detected new block
[2018-01-20 13:59:19] accepted: 15/15 (100.00%), 754.01 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:20] accepted: 16/16 (100.00%), 759.75 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:43] accepted: 17/17 (100.00%), 714.86 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:44] accepted: 18/18 (100.00%), 714.63 H/s at diff 3206 (yay!!!)

i ran patricks docker run -d -e username=example@example.com servethehome/monero_cpu_minergate
Watts went up from 175 to 269.

I dont know enough about docker to know if it using both cpu or not, etc.

Bradford · Jan 20, 2018

marcoi said:

Code:

[2018-01-20 13:57:10] Using JSON-RPC 2.0
[2018-01-20 13:57:10] Starting Stratum on stratum+tcp://xmr.pool.minergate.com:45560
[2018-01-20 13:57:10] 30 miner threads started, using 'cryptonight' algorithm.
[2018-01-20 13:57:10] Pool set diff to 1063
[2018-01-20 13:57:10] Stratum detected new block
[2018-01-20 13:57:11] accepted: 1/1 (100.00%), 719.90 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:12] accepted: 2/2 (100.00%), 716.61 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:19] accepted: 3/3 (100.00%), 710.53 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:24] accepted: 4/4 (100.00%), 712.24 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:24] accepted: 5/5 (100.00%), 707.54 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:27] accepted: 6/6 (100.00%), 725.14 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:27] accepted: 7/7 (100.00%), 732.42 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:28] Pool set diff to 4148
[2018-01-20 13:57:28] Stratum detected new block
[2018-01-20 13:57:33] accepted: 8/8 (100.00%), 717.00 H/s at diff 4148 (yay!!!)
[2018-01-20 13:57:40] accepted: 9/9 (100.00%), 709.72 H/s at diff 4148 (yay!!!)
[2018-01-20 13:57:41] Pool set diff to 5310
[2018-01-20 13:57:41] Stratum detected new block
[2018-01-20 13:57:41] accepted: 10/10 (100.00%), 715.22 H/s at diff 5310 (yay!!!)
[2018-01-20 13:57:57] accepted: 11/11 (100.00%), 747.94 H/s at diff 5310 (yay!!!)
[2018-01-20 13:58:45] accepted: 12/12 (100.00%), 750.64 H/s at diff 5310 (yay!!!)
[2018-01-20 13:58:53] accepted: 13/13 (100.00%), 721.28 H/s at diff 5310 (yay!!!)
[2018-01-20 13:59:02] accepted: 14/14 (100.00%), 716.12 H/s at diff 5310 (yay!!!)
[2018-01-20 13:59:19] Pool set diff to 3206
[2018-01-20 13:59:19] Stratum detected new block
[2018-01-20 13:59:19] accepted: 15/15 (100.00%), 754.01 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:20] accepted: 16/16 (100.00%), 759.75 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:43] accepted: 17/17 (100.00%), 714.86 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:44] accepted: 18/18 (100.00%), 714.63 H/s at diff 3206 (yay!!!)

i ran patricks docker run -d -e username=example@example.com servethehome/monero_cpu_minergate
Watts went up from 175 to 269.

I dont know enough about docker to know if it using both cpu or not, etc.

This is great, thanks. I bet someone else who has used that docker image can chime in on whether it will automatically configure 2 CPUs in a case like this.

Joel · Jan 20, 2018

When I first started mining I used the minergate image. It does not configure NUMA affinity.

I speculate that ~900h/s is the best there is for (x2 of) this processor.

Iaroslav · Jan 20, 2018

Bradford said:
That was with 2 CPUs?

Sure. It's XMR hashes on 2 CPUs with xmr-stak-cpu.

marcoi · Jan 20, 2018

I can try another miner just need link to build instructions for Ubuntu.

Joel · Jan 20, 2018

Sure, could you paste the output of numactl first though?

Bradford · Jan 20, 2018

marcoi said:

Code:

[2018-01-20 13:57:10] Using JSON-RPC 2.0
[2018-01-20 13:57:10] Starting Stratum on stratum+tcp://xmr.pool.minergate.com:45560
[2018-01-20 13:57:10] 30 miner threads started, using 'cryptonight' algorithm.
[2018-01-20 13:57:10] Pool set diff to 1063
[2018-01-20 13:57:10] Stratum detected new block
[2018-01-20 13:57:11] accepted: 1/1 (100.00%), 719.90 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:12] accepted: 2/2 (100.00%), 716.61 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:19] accepted: 3/3 (100.00%), 710.53 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:24] accepted: 4/4 (100.00%), 712.24 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:24] accepted: 5/5 (100.00%), 707.54 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:27] accepted: 6/6 (100.00%), 725.14 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:27] accepted: 7/7 (100.00%), 732.42 H/s at diff 1063 (yay!!!)
[2018-01-20 13:57:28] Pool set diff to 4148
[2018-01-20 13:57:28] Stratum detected new block
[2018-01-20 13:57:33] accepted: 8/8 (100.00%), 717.00 H/s at diff 4148 (yay!!!)
[2018-01-20 13:57:40] accepted: 9/9 (100.00%), 709.72 H/s at diff 4148 (yay!!!)
[2018-01-20 13:57:41] Pool set diff to 5310
[2018-01-20 13:57:41] Stratum detected new block
[2018-01-20 13:57:41] accepted: 10/10 (100.00%), 715.22 H/s at diff 5310 (yay!!!)
[2018-01-20 13:57:57] accepted: 11/11 (100.00%), 747.94 H/s at diff 5310 (yay!!!)
[2018-01-20 13:58:45] accepted: 12/12 (100.00%), 750.64 H/s at diff 5310 (yay!!!)
[2018-01-20 13:58:53] accepted: 13/13 (100.00%), 721.28 H/s at diff 5310 (yay!!!)
[2018-01-20 13:59:02] accepted: 14/14 (100.00%), 716.12 H/s at diff 5310 (yay!!!)
[2018-01-20 13:59:19] Pool set diff to 3206
[2018-01-20 13:59:19] Stratum detected new block
[2018-01-20 13:59:19] accepted: 15/15 (100.00%), 754.01 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:20] accepted: 16/16 (100.00%), 759.75 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:43] accepted: 17/17 (100.00%), 714.86 H/s at diff 3206 (yay!!!)
[2018-01-20 13:59:44] accepted: 18/18 (100.00%), 714.63 H/s at diff 3206 (yay!!!)

i ran patricks docker run -d -e username=example@example.com servethehome/monero_cpu_minergate
Watts went up from 175 to 269.

I dont know enough about docker to know if it using both cpu or not, etc.

That seems like high wattage for only one CPU, but I don't have any reference, just looks like it's using both based on that.

marcoi said:
I can try another miner just need link to build instructions for Ubuntu.

xmrig looks like it has a precompiled binary you can use: Releases · xmrig/xmrig · GitHub

Joel · Jan 20, 2018

Try this out (if you don't use nicehash just change the pool target):

Edit: This is assuming 1 CPU. The second instance is designed to target any available Hyper threaded cores that have "bandwidth." For 2 CPUs you'd run 4 instances.

docker run -itd -e -o stratum+tcp://cryptonight.usa.nicehash.com:3355 -e username=xxxxxxxx -e numthread=10 -e cpuset_cpus"0-9" servethehome/monero_xmrig

docker run -itd -e -o stratum+tcp://cryptonight.usa.nicehash.com:3355 -e username=xxxxxxxx -e numthread=4 -e cpuset_cpus"12-23" servethehome/monero_xmrig

This is following @funkywizard's guide from this post:

https://forums.servethehome.com/ind...ra-aeon-mining-performance.17853/#post-172438

marcoi · Jan 20, 2018

Joel said:
Try this out (if you don't use nicehash just change the pool target):

Edit: This is assuming 1 CPU. The second instance is designed to target any available Hyper threaded cores that have "bandwidth." For 2 CPUs you'd run 4 instances.

docker run -itd -e -o stratum+tcp://cryptonight.usa.nicehash.com:3355 -e username=xxxxxxxx -e numthread=10 -e cpuset_cpus"0-9" servethehome/monero_xmrig

docker run -itd -e -o stratum+tcp://cryptonight.usa.nicehash.com:3355 -e username=xxxxxxxx -e numthread=4 -e cpuset_cpus"12-23" servethehome/monero_xmrig

This is following @funkywizard's guide from this post:

https://forums.servethehome.com/ind...ra-aeon-mining-performance.17853/#post-172438

something is off with command im getting error when trying to run it
docker: invalid reference format.
See 'docker run --help'.

Anyone here tried the Xeon E5-2651 V2?

Member

Member

Active Member

Member

Active Member

Active Member

Well-Known Member

Member

Well-Known Member

Active Member

Active Member

Well-Known Member

Active Member

Active Member

Member

Well-Known Member

Active Member

Active Member

Active Member

Well-Known Member