OK I (think I) successfully flashed my newly acquired IBM M1015 to LSI9211-8i in IT mode.
It was a bit difficult as I needed to find a motherboard that could see the card AND flash it.
The first I tried saw the card, but froze when trying to query the card before flashing.
Next motherboard was fine.
Anyway I flashed it as seen here:
http://www.servethehome.com/ibm-serveraid-m1015-part-4/
and here:
SAS2008 (LSI9240/9211) Firmware files - Page 4 - Projects, Tools, Utilities & Customized INFs - LaptopVideo2Go Forums
I used P16 release firmware.
Note #1: None of the two was the actual motherboard I would use the card on. The card that I want the card on is ECS P45T-A (V1.0).
ECS Web Site > P45T-A (V1.0)
On the first PCIe x16 slot I have the VGA card and on the second PCIe x16 slot I have the controller.
Note #2: I NEVER tried it as IBM M1015 with disks (my SFF-8087 to 2xSATA cables were on order).
Anyway I installed everything on my server, put the cables in, connected 8 of my drives (note that the drives where previously working already in that system, using two smaller "stupid" controllers). So, nothing wrong with the drives, or PSU etc.
Anyway long story short: Doesn't seem to see ANY of my drives. It shows 0 drives. Also I installed MSM in Windows, it does indeed see the card, but shows 0 drives.
What could be wrong?
Extra info. When booting, BIOS screen reports:
LSI MPT SAS2 BIOS
MPT2BIOS 7.31.00.00 (2013.02.28)
And, in the ctrl-c prompt if I PRESS ctrl-c it shows:
LSI Corporation MPT2 boot ROM successfully installed.
(briefly)
...then boots and actuallyu does NOT go to configuration.
If I do NOT press ctrl-c, instead it shows a table with this info:
PCI slot FF
Vendor LSI
SAS2008-IT
revision 16.00.00.00
size/nvdata 10:00:00:00:06
...and boots
Windows (SBS2011 which is 2008R2 kernel), does see the card, I even installed newest drivers, but again, no drives.
Give me some feedback please.
Could it be the cables?
These are the cables:
Digitus DK-127011 SAS,SFF-8087,36PIN ΣΕ 4 SATA 7 P... - Easy Buy World
(bought two)
Please help me, I don't know what to do.
It was a bit difficult as I needed to find a motherboard that could see the card AND flash it.
The first I tried saw the card, but froze when trying to query the card before flashing.
Next motherboard was fine.
Anyway I flashed it as seen here:
http://www.servethehome.com/ibm-serveraid-m1015-part-4/
and here:
SAS2008 (LSI9240/9211) Firmware files - Page 4 - Projects, Tools, Utilities & Customized INFs - LaptopVideo2Go Forums
I used P16 release firmware.
Note #1: None of the two was the actual motherboard I would use the card on. The card that I want the card on is ECS P45T-A (V1.0).
ECS Web Site > P45T-A (V1.0)
On the first PCIe x16 slot I have the VGA card and on the second PCIe x16 slot I have the controller.
Note #2: I NEVER tried it as IBM M1015 with disks (my SFF-8087 to 2xSATA cables were on order).
Anyway I installed everything on my server, put the cables in, connected 8 of my drives (note that the drives where previously working already in that system, using two smaller "stupid" controllers). So, nothing wrong with the drives, or PSU etc.
Anyway long story short: Doesn't seem to see ANY of my drives. It shows 0 drives. Also I installed MSM in Windows, it does indeed see the card, but shows 0 drives.
What could be wrong?
Extra info. When booting, BIOS screen reports:
LSI MPT SAS2 BIOS
MPT2BIOS 7.31.00.00 (2013.02.28)
And, in the ctrl-c prompt if I PRESS ctrl-c it shows:
LSI Corporation MPT2 boot ROM successfully installed.
(briefly)
...then boots and actuallyu does NOT go to configuration.
If I do NOT press ctrl-c, instead it shows a table with this info:
PCI slot FF
Vendor LSI
SAS2008-IT
revision 16.00.00.00
size/nvdata 10:00:00:00:06
...and boots
Windows (SBS2011 which is 2008R2 kernel), does see the card, I even installed newest drivers, but again, no drives.
Give me some feedback please.
Could it be the cables?
These are the cables:
Digitus DK-127011 SAS,SFF-8087,36PIN ΣΕ 4 SATA 7 P... - Easy Buy World
(bought two)
Please help me, I don't know what to do.